SAMPLE CUTTING PRESS
Technical Specifications
-
Operation Type: Manual / Hydraulic / Pneumatic
-
Capacity: 5 kN – 50 kN (or higher as per model)
-
Cutting Force Control: Lever / Hydraulic hand pump / Air pressure
-
Stroke Length: Adjustable stroke
-
Working Table: Hardened steel or aluminum base plate
-
Die Holder: Quick-change die holder
-
Cutting Area: Approx. 150 × 150 mm to 300 × 300 mm
-
Pressure Indication: Pressure gauge (for hydraulic/pneumatic models)
-
Frame Construction: Heavy-duty steel frame
-
Safety Features: Safety guard / Two-hand operation (model dependent)
-
Power Supply: Not required (manual) / 230V AC (motorized hydraulic)
-
Applications: Rubber, plastic sheets, foam, leather, paperboard, textile samples
A Sample Cutting Press is a precision laboratory machine used to cut uniform test specimens from materials such as rubber, plastic, leather, textiles, paper, composites, and packaging sheets. It uses a controlled vertical pressing action with interchangeable cutting dies to produce accurate, repeatable samples required for physical and mechanical testing. The machine ensures clean edges, consistent dimensions, and minimal material distortion.
Key Features
-
High precision specimen cutting
-
Uniform and repeatable sample size
-
Quick die change system
-
Rugged construction
-
Smooth vertical pressing action
-
Low maintenance
-
Suitable for laboratory and QA use
-
Compatible with standard cutting dies
Related products
PIN ON DISC WEAR TESTING MACHINE
Technical Specifications (Typical)
-
Test Type: Dry / Lubricated sliding wear test
-
Principle: Pin-on-disc tribological method
-
Disc Diameter: 100–165 mm (customizable)
-
Disc Material: Hardened alloy steel (or as required)
-
Speed Range: 100 – 2000 RPM (variable)
-
Load Range: 5 N to 200 N (dead weight or lever loading system)
-
Wear Track Radius: Adjustable
-
Friction Force Measurement: Strain gauge / load cell based
-
Coefficient of Friction Display: Digital real-time display
-
Wear Measurement: Linear displacement sensor / LVDT
-
Motor: Variable speed DC / AC motor with controller
-
Data Display: Digital display / Computerized interface (optional)
-
Data Output: USB / Software-based data logging (optional)
-
Power Supply: 220–240V AC, 50 Hz
-
Safety Features: Guard cover, overload protection
-
Standards Compliance: ASTM G99 / ISO 7148 (or equivalent)
UNIVERSAL-TESTING-MACHINE
Technical Specifications
Load Capacity Range
-
From: 1 kN to 2000 kN (or higher depending on model)
-
Common ranges: 10 kN, 50 kN, 100 kN, 200 kN, 600 kN, 1000 kN
Machine Types
-
Electromechanical UTM
-
Servo Hydraulic UTM
-
Computerized / Digital UTM
Control Modes
-
Load control
-
Displacement control
-
Strain control
-
Pace rate control
Accuracy
-
Load accuracy: ±0.5% to ±1% of indicated load
-
Class 0.5 / Class 1 as per ISO standards
Load Measurement
-
High precision load cell
-
Multiple load cell options
Crosshead Travel
-
Typically 600–1200 mm (model dependent)
Speed Range
-
Very low to high test speeds
-
Example: 0.001 to 500 mm/min
Data Acquisition
-
Real-time force vs displacement curve
-
Stress–strain graph generation
-
PC based software with test reports
Safety Features
-
Overload protection
-
Emergency stop
-
Limit switches
-
Safety guards
Standards Compliance
-
ASTM
-
ISO
-
IS
-
EN
-
DIN
Common Tests Performed
-
Tensile test
-
Compression test
-
Flexural test
-
Shear test
-
Peel test
-
Tear test
-
Bend test
LOAD TESTING MACHINE
Technical Specifications
-
Load Capacity Range: 50 kN to 5000 kN (customizable)
-
Type: Hydraulic / Electro-Mechanical
-
Control Mode: Manual / Semi-Automatic / Computerized
-
Load Measurement: Digital Load Cell / Pressure Sensor
-
Accuracy: ±1% or better
-
Display: Digital indicator / Computer software display
-
Resolution: High resolution load reading
-
Loading Rate Control: Adjustable
-
Frame Construction: Heavy-duty steel frame
-
Power Supply: 220V / 415V AC
-
Hydraulic System: Motorized hydraulic power pack
-
Data Output: USB / RS232 / Software-based reporting (computerized models)
-
Safety Features: Overload protection, emergency stop
-
Test Modes: Compression / Tension / Flexural (depending on model)
-
Standards Compliance: IS / ASTM / BS / EN standards (model dependent)
COMPUTERIZED TENSILE TESTING MACHINE
Technical Specifications (Typical)
-
Capacity Range: 1 kN to 1000 kN (or higher on request)
-
Drive System: Servo motor / AC variable frequency drive / Hydraulic (as per model)
-
Load Measurement: High-precision strain gauge load cell
-
Accuracy: ±1% or better of indicated load
-
Crosshead Speed: 0.01 to 500 mm/min (programmable)
-
Speed Accuracy: ±1%
-
Stroke Length: 800 – 1200 mm (customizable)
-
Grips: Wedge, pneumatic, hydraulic, compression platens, bending fixtures
-
Control Mode: Load, displacement, and strain control
-
Software: PC-based testing software with graph plotting, test methods, and report generation
-
Data Output: Load vs extension, stress vs strain curves
-
Safety Features: Overload protection, limit switches, emergency stop
-
Power Supply: 230V / 415V AC, 50 Hz
-
Standards Compliance: ASTM E8, ASTM A370, ISO 6892, BIS standards
VASLIC RUB FASTNESS TESTER
Technical Overview
✔ Test Principle:
-
A wool felt rubbing pad (dry or wet) repeatedly rubs the sample surface under a specified pressure and stroke.
-
After a set number of cycles, color transfer and surface changes are assessed visually, typically using a grey scale for staining and color change.
✔ Typical Specifications
-
Rubbing Head Area: ~15 mm × 15 mm
-
Rubbing Speed: ~40 ± 2 cycles per minute
-
Rubbing Stroke: ~35–40 mm
-
Weight (Pressure): ~500 g finger + optional 500 g additional weight (total ~1000 g)
-
Sample Size: ~120 × 20 mm
-
Sample Tension Range: ~0–20 %
-
Power Supply: ~AC 220 V 50/60 Hz
-
Automatic Cycle Counter: Digital or mechanical with automatic stop upon reaching preset cycles
✔ Testing Conditions:
-
Dry rubbing
-
Wet rubbing (sample and/or felt soaked as per standard procedures)
✔ Compliance Standards:
Common standards this tester supports:
-
ISO 11640 – Colour fastness to rubbing (leather)
-
DIN 4843 – Leather colour fastness
-
SATRA TM173 / TM177 – Rubbing fastness methods
-
EN ISO 20344:7.3 – Footwear upper and lining tests
-
ISO 17700 Method A – Footwear material colour fastness
MARTINDALE ABRASION TESTER
Technical Specifications
-
Test Method: Martindale Abrasion & Pilling Method
-
Motion: Lissajous figure (multi-directional rubbing)
-
Number of Test Stations: 4 / 6 / 8 / 9 / 12 / 16 stations (optional)
-
Specimen Diameter: 38 mm or 140 mm (as per standard)
-
Abrasive Medium: Standard wool fabric / sandpaper
-
Applied Pressure:
-
9 kPa (Light fabrics)
-
12 kPa (Workwear, upholstery)
-
-
Counter Range: 0 – 99,999 cycles (digital presettable)
-
Drive System: Precision motor with gearbox
-
Control System: Microprocessor / Digital controller
-
Display: LCD / LED digital display
-
Auto Stop: Yes, at preset cycles
-
Power Supply: 220–240 V AC, 50 Hz
-
Standards Compliance:
-
ISO 12947
-
ASTM D4966
-
BS 3424
-
EN 530
-
GB/T 21196
-
Applications
-
Abrasion resistance testing of woven & knitted fabrics
-
Pilling resistance evaluation
-
Upholstery and automotive textile testing
-
Carpet and floor covering testing
-
Quality control and R&D
FLEXO- METER
Technical Specifications
-
Measuring Principle: Cantilever bending method
-
Test Parameter: Bending length / Stiffness
-
Specimen Width: Typically 25 mm (as per standards)
-
Specimen Length: Adjustable
-
Measurement Range: Suitable for low to high stiffness materials
-
Scale Type: Direct reading scale / Graduated scale
-
Accuracy: High precision with repeatable results
-
Operation: Manual / Semi-automatic (model dependent)
-
Construction: Rigid metal body with corrosion-resistant finish
-
Clamping System: Precision specimen holder for accurate positioning
-
Standards Compliance:
-
ISO 2493
-
TAPPI T489
-
BS 3748
-
Applications
-
Paper & Paperboard testing
-
Packaging material evaluation
-
Carton & corrugated box testing
-
Printing & publishing industry
-
Quality control & R&D laboratories
SAMPLE CUTTING PRESS
Technical Specifications
(Specifications may vary by model and capacity)
-
Type: Hydraulic / Pneumatic / Manual Sample Cutting Press
-
Capacity: 5 Ton / 10 Ton / 20 Ton / 25 Ton / 30 Ton (or as required)
-
Pressing Area: 300 × 300 mm to 500 × 500 mm
-
Daylight Gap: 100 – 250 mm
-
Ram Stroke: Adjustable
-
Pressure Control: Manual / Digital Pressure Gauge
-
Operation Mode: Push Button / Foot Switch / Dual Hand Safety Control
-
Cutting Accuracy: High repeatability with clean edges
-
Platen Material: Hardened Steel / EN-grade Steel
-
Frame Construction: Heavy-duty welded steel frame
-
Power Supply: 230V / 415V AC, 50 Hz
-
Safety Features: Emergency stop, overload protection, safety guard
-
Standards Compliance: ASTM, ISO, IS, DIN, BS
Applications
-
Rubber and plastic testing laboratories
-
Automotive and aerospace material testing
-
Textile and leather industries
-
Packaging and polymer testing
-
Quality control and R&D labs
Key Features
-
Uniform cutting pressure
-
Rugged and vibration-free structure
-
Easy die replacement
-
Low maintenance operation
-
High operator safety
-
Suitable for standard and custom dies
Reviews
There are no reviews yet.